If only input values of unit were changed and unit is remained the same, click “Export to MagiCAD and update unit”. Calculate unit again and click MagiCAD export –button to update the unit in MagiCAD.
The list of units in selected project is presented in dialog and user selects the editable unit.įlexit program opens and calculated values from MagiCAD are as input values. With Open Flexit project -button user is supposed to open Flexit program project file where the editable unit is saved. Note! Possible kitchen hood connection in the middle of the unit is always shown but it is not taken account when updating data to program. Pressure drop values from MagiCAD as follows: Pressure drop values are summation of total pressure drops in supply & outdoor and extract & exhaust systems. Supply and extract air flows from MagiCAD as follows: Air flow values show the biggest airflow value in supply air (supply or outdoor system) and the biggest airflow value in extract air (extract or exhaust system). The data which will be exported to Flexit program, as a new default data, is presented in this dialog as follows:. After pressing update -button, select unit from the drawing and the following update dialog opens. At least one system must be connected and calculated. button to update unit, you must connect duct connectionsĪnd run MagiCAD function “Flow summation and balancing” for systems. There is no possibility to change any selection, only view. Values are not updated by MagiCAD calculations. In this dialog you are able to see unit data which was exported into MagiCAD from Flexit program. View AHU data Press -button to open Unit’s information dialog. Duct heater do not have any data, so it is not taken account in MagiCAD calculation but it can be connected to duct system. supply system, then its combo will be enabled and user may select system.įrom version 2013.3.1 there is possibility also to export duct heater to MagiCAD with UNI3 and UNI4 air handling units.ĭuct heater is just simply added to drawing after unit. MagiCAD system – select preferred system for AHU unit.Ĭonnections – if there is only one of the each MagiCAD system, then combos are filled automatically. If checkbox is not checked, the duct connections at the bottom of the unit are not shown in drawing. Those units have more than one outdoor and extract duct connections.
Installation height – unit bottom height in drawingĪllow two connections – selection is enabled for unit sizes 3 and 4. Input or select the following information: When Export to MagiCAD-button is pressed and following message appears, itĪfter you have added unit to MagiCAD project, dialog opens. Now unit is ready to be exported to MagiCAD. button or open dialog from File->Export…. After unit is calculated, MagiCAD export –button Press In Flexit program, create new unit or open project file. button in MagiCAD and Flexit program starts.
How to use the plugin Inserting AHU unit Press Next time you use AutoCAD, the customization file is automatically loaded. When you click Load, Flexit toolbar appears on the desktop. When you first time start using Flexit MagiCAD plugin you need to load the customization file (FlexitMagi.cuix) manually. Run CUILOAD or MENULOAD in AutoCAD, and browse the customization file from the directory where you installed the program (by default, the directory is C:\Program Files\Flexit). Starting the program Before you start using Flexit MagiCAD Plugin, start MagiCAD and open a Ventilation project. Note if you have several AutoCAD versions on your workstation: Before you run the installation program, start MagiCAD to make sure that Flexit MagiCAD plugin installs on the same AutoCAD platform as MagiCAD. The 64-bit version of the program is installed by running the installation programs Flexit 2013.10.1.msi and Flexit MagiCAD plugin 2013.10.1 64-bit.msiĪdministrator privileges are recommended for installation.
The 32-bit version of the program is installed by running the installation program (includes both calculation software and plugin) Flexit 2013.10.1.msi The installation package is available at Progman´s website Flexit Installing the software Required third-party software Flexit MagiCAD plugin works with the following MagiCAD for AutoCAD versions 6Ībout this document This document contains instructions on using Flexit MagiCAD plugin. 3 Inserting AHU unit View AHU data Update AHU unit